For laboratory research use only. Not for human or veterinary use. Read our research-use policy

Analytical methods

Amino acid analysis and peptide quantification

HPLC tells you how pure a peptide is, not how much of it there is. Measuring quantity, whether as net peptide content in a powder or as the concentration of a solution, needs a different set of methods.

Published 18 November 2026

What these methods are for

Quantification methods answer the question "how much peptide is actually here?" For a lyophilised powder, the answer is usually expressed as net peptide content. For a solution, it is a concentration. Both matter because peptide powders contain counter-ions, water and other non-peptide mass. See Net peptide content and stock solution concentration.

Amino acid analysis (AAA)

How it works

  1. Hydrolysis. The peptide is broken down into its free amino acids, classically in 6 M hydrochloric acid at about 110 °C for around 24 hours, in a sealed tube under vacuum or inert gas.
  2. Derivatisation. Most amino acids absorb little UV light and do not fluoresce, so they are reacted with a reagent that makes them detectable. This can be done after separation (post-column, classically with ninhydrin following ion-exchange chromatography) or before separation (pre-column, with reagents such as o-phthalaldehyde (OPA), FMOC-Cl, phenyl isothiocyanate (PITC) or AQC, followed by reversed-phase HPLC).
  3. Separation and quantification. Each amino acid is measured against calibration standards.

What it measures

AAA gives two things. The relative amounts of each amino acid are compared with the ratios expected from the sequence, which supports identity. The absolute amounts, compared with the weighed sample mass, give the net peptide content. Calculations are normally based on the amino acids that survive hydrolysis well, rather than on every residue.

Limitations

ResidueWhat happens during acid hydrolysisCommon workaround
TryptophanLargely destroyedAlternative hydrolysis (for example with methanesulfonic acid) or measurement by another method
Cysteine / cystinePartially destroyed; poorly recoveredPerformic acid oxidation to cysteic acid before hydrolysis, or alkylation
MethioninePartially oxidisedPerformic acid oxidation to methionine sulfone before hydrolysis
Asparagine and glutamineConverted to aspartic and glutamic acidReported combined as Asx and Glx; the amide forms cannot be distinguished
Serine and threonineGradually destroyedCorrection factors, or extrapolation from several hydrolysis times
Isoleucine and valineBonds between these bulky residues hydrolyse slowlyLonger hydrolysis times

AAA also cannot tell you the order of the residues, cannot distinguish D- from L-amino acids without a chiral method, and does not detect non-amino-acid parts of the molecule such as labels. It consumes sample and is usually run by specialist laboratories. The amino acid content it reports includes peptide-related impurities, which is why it is reported alongside, not instead of, HPLC purity.

Elemental nitrogen analysis

Combustion (CHN) analysis measures the percentage of nitrogen in a sample. Because the peptide's nitrogen content can be calculated exactly from its molecular formula, the ratio of measured to theoretical nitrogen gives an estimate of net peptide content:

  • Net peptide content ≈ measured nitrogen (%) ÷ theoretical nitrogen of the peptide (%)

The method is fast and needs only a few milligrams, but it assumes all the nitrogen comes from the peptide. Nitrogen-containing counter-ions (such as ammonium), residual nitrogen-containing solvents (such as acetonitrile or DMF) or other contaminants inflate the result. Trifluoroacetate and acetate counter-ions contain no nitrogen, so they do not interfere. Unlike AAA, nitrogen analysis gives no information about composition.

UV absorbance

UV absorbance is the quickest way to measure the concentration of a peptide solution, using the Beer–Lambert law: concentration = absorbance ÷ (molar absorption coefficient × path length).

A280

Absorbance at 280 nm comes mainly from tryptophan and tyrosine, with a small contribution from cystine. The molar absorption coefficient can be estimated from the sequence using values published by Pace and colleagues (approximately 5,500 M−1cm−1 per tryptophan, 1,490 per tyrosine and 125 per cystine). This works well for peptides containing tryptophan or tyrosine, but not at all for those without them, and the estimate is less reliable when there are only one or two absorbing residues.

A205 and A214

The peptide bond itself absorbs strongly at around 205–214 nm, so far-UV absorbance can be used for peptides that lack aromatic residues. Coefficients can be estimated from the sequence (see Anthis and Clore, below). The drawbacks are that many buffer components, organic solvents and impurities also absorb strongly in this region, so the buffer must be chosen carefully and matched in the blank, and the measurement is more sensitive to contamination than A280.

Points to remember

  • UV methods measure everything that absorbs at that wavelength, including peptide-related impurities.
  • Particles and aggregates scatter light and raise apparent absorbance; centrifuge or filter first.
  • UV absorbance measures a solution. It does not give net peptide content directly unless the solution was prepared from a known mass of powder.

Choosing a method

MethodTypical useMain strengthsMain limitations
Amino acid analysisNet peptide content on a COA; composition checkAbsolute quantity plus compositionResidue losses; specialist method; uses sample
Elemental nitrogenNet peptide content on a COAFast; small sample; simple calculationAny non-peptide nitrogen interferes; no composition information
A280Checking stock solution concentration in the labQuick, non-destructive, widely availableNeeds Trp or Tyr; estimate-based coefficient
A205 / A214Solutions of peptides without aromatic residuesApplies to almost any peptideStrong interference from buffers and impurities

In practice, a COA's net peptide content usually comes from AAA or nitrogen analysis, and laboratories use UV absorbance to check solutions they have prepared. Related: How to read a peptide Certificate of Analysis and TFA and other counter-ions.

Related

Sources and further reading

  • United States Pharmacopeia, General Chapter <1052> Biotechnology-Derived Articles: Amino Acid Analysis.
  • Pace CN, Vajdos F, Fee L, Grimsley G, Gray T. How to measure and predict the molar absorption coefficient of a protein. Protein Science. 1995;4(11):2411–2423.
  • Anthis NJ, Clore GM. Sequence-specific determination of protein and peptide concentrations by absorbance at 205 nm. Protein Science. 2013;22(6):851–858.

Frequently asked questions

What does amino acid analysis measure?

The amount of each amino acid after hydrolysis, which gives peptide quantity. It cannot give residue order or distinguish D- from L-amino acids without a chiral method.

How does nitrogen analysis estimate net peptide content?

Net peptide content is roughly measured nitrogen (%) divided by the peptide's theoretical nitrogen (%). Trifluoroacetate and acetate contain no nitrogen and do not interfere; ammonium or nitrogen-containing solvents inflate the result.

What is the quickest way to measure a peptide solution's concentration?

UV absorbance with the Beer-Lambert law: concentration = absorbance / (molar absorption coefficient x path length).

Why are Asn and Gln reported together with Asp and Glu?

Acid hydrolysis converts asparagine and glutamine to the acids, so AAA reports Asx and Glx and cannot tell the amide forms apart.