Laboratory practice
Net peptide content and stock solution concentration
The mass on the balance is not the mass of peptide. Counter-ions, bound water and impurities all contribute to what you weigh, so accurate molar concentrations need a correction.
Three numbers that are easy to confuse
| Term | What it describes | Typical source |
|---|---|---|
| Gross weight | The total mass of lyophilised powder: peptide plus counter-ions, bound water and any residual salts or solvents | The balance; the fill weight on the label |
| Net peptide content (NPC) | The percentage of the gross weight that is peptide (all peptidic material, including peptide-related impurities) | Amino acid analysis or elemental nitrogen analysis |
| HPLC purity | The percentage of the peptidic material, measured by UV peak area, that is the target sequence | Reversed-phase HPLC with UV detection |
A product can be 98% pure by HPLC and still have a net peptide content well below 100%. The two figures answer different questions: purity says how much of the peptide material is the right peptide; net peptide content says how much of the powder is peptide at all. Lyophilised peptides are hygroscopic salts, so net peptide content is routinely below 100%, and peptides with many basic residues tend to carry more counter-ion mass. See TFA and other counter-ions in synthetic peptides for why.
Which molecular weight to use
Net peptide content is expressed relative to the peptide itself, without its counter-ions. When you correct with net peptide content, use the molecular weight of the peptide (the free-base form calculated from its sequence and modifications), not a salt-form molecular weight. If a COA quotes a molecular weight that already includes counter-ions, do not also apply a net peptide content correction for the same counter-ions, or you will correct twice.
The calculation
For a stock solution of molar concentration C and volume V:
- Peptide mass needed (mg) = C (mmol/L) × V (L) × MW (g/mol)
- Powder mass to weigh (mg) = peptide mass needed ÷ (NPC as a fraction)
If you want the concentration of the target sequence specifically, rather than of all peptidic material, also divide by the HPLC purity as a fraction. For most purposes the purity correction is small compared with the net peptide content correction, but record which correction you applied so results can be compared between batches.
Worked example (illustrative values only)
The figures below are invented to show the arithmetic. They do not describe any real product.
| Parameter | Example value |
|---|---|
| Peptide | "Example peptide X" (hypothetical) |
| Molecular weight (peptide, free base) | 1,500.0 g/mol |
| Net peptide content | 75% |
| HPLC purity | 98% |
| Target stock | 1.0 mL of a 1.0 mM solution for an in-vitro assay |
- Peptide mass needed = 1.0 mmol/L × 0.0010 L × 1,500.0 g/mol = 1.50 mg.
- Powder to weigh, correcting for net peptide content = 1.50 mg ÷ 0.75 = 2.00 mg.
- If you also correct for purity = 1.50 mg ÷ (0.75 × 0.98) = 2.04 mg.
Without the correction, weighing 1.50 mg of powder would give a solution of about 0.75 mM, a 25% error before any other source of variation.
Weigh first, then calculate the volume
Weighing exactly 2.00 mg is difficult without a microbalance, and small masses carry large relative errors. It is usually more accurate to weigh a larger, convenient amount, record the exact mass, and calculate the volume to add:
- Volume (L) = powder mass (mg) × NPC ÷ (MW (g/mol) × C (mmol/L))
Continuing the example: if you weigh 5.12 mg of powder, the peptide content is 5.12 × 0.75 = 3.84 mg, which is 2.56 µmol. For a 1.0 mM stock, add solvent to a final volume of 2.56 mL.
Practical points
- Let a cold vial reach room temperature before opening it, so moisture does not condense on the hygroscopic powder and change its mass. See Storing lyophilised research peptides.
- Use the net peptide content for the specific batch you are weighing. It varies from batch to batch, even for the same sequence and salt form.
- If no net peptide content is reported, treat any concentration calculated from gross weight as approximate, or determine the concentration of the solution directly. See Amino acid analysis and peptide quantification.
- Record the batch number, NPC, purity, molecular weight and the corrections used alongside each stock solution.
Related: How to read a peptide Certificate of Analysis.
Related
- TFA to acetate: peptide counter-ion exchange
- Peptide adsorption to vials and plastics
- Peptide purity vs peptide content: a worked vial mass balance and counter-ion estimates
- Peptide reconstitution calculator
Sources and further reading
- United States Pharmacopeia, General Chapter <1503> Quality Attributes of Synthetic Peptide Drug Substances.
- United States Pharmacopeia, General Chapter <1052> Biotechnology-Derived Articles: Amino Acid Analysis.
Frequently asked questions
What is the difference between gross weight, net peptide content and HPLC purity?
Gross weight is the whole powder; net peptide content is the percentage of it that is peptide material; HPLC purity is the percentage of the peptidic material that is the target sequence.
How do I correct a stock concentration for net peptide content?
Peptide mass needed (mg) = concentration (mmol/L) x volume (L) x molecular weight (g/mol); the powder to weigh is that mass divided by the net peptide content as a fraction.
Which molecular weight should I use?
The free-base peptide weight calculated from the sequence and modifications. If a COA quotes a weight that already includes counter-ions, do not also apply a net peptide content correction for them.
Is a 98% pure peptide 98% peptide by weight?
No. Purity describes the peptidic material; the powder also contains counter-ions and water, so net peptide content is routinely below 100%.