For laboratory research use only. Not for human or veterinary use. Read our research-use policy

Laboratory practice

Dissolving peptides for in-vitro assays

There is no single solvent that suits every peptide. A few minutes spent working out a sequence's charge and hydrophobicity usually tells you where to start, and testing a small portion first protects the rest of the material.

Published 18 November 2026

Start with the sequence

Solubility depends mainly on two properties you can estimate from the sequence: the net charge at the pH you plan to use, and the proportion of hydrophobic residues. Length, secondary structure and the tendency to aggregate also matter, so treat these rules as a starting point rather than a guarantee.

Estimating net charge

A simple estimate at around neutral pH:

  • Count +1 for each lysine (K) and arginine (R), and for a free N-terminal amine.
  • Count −1 for each aspartic acid (D) and glutamic acid (E), and for a free C-terminal carboxyl.
  • Histidine (H) is largely uncharged at neutral pH but positively charged under acidic conditions.
  • Adjust for modifications: N-terminal acetylation removes the N-terminal positive charge, and C-terminal amidation removes the C-terminal negative charge. See Peptide modifications explained.

Judging hydrophobicity

Peptides with a high proportion of hydrophobic residues (such as leucine, isoleucine, valine, phenylalanine, tryptophan, methionine and alanine), and few charged residues, are often poorly soluble in water. A common rule of thumb is that peptides with around half or more hydrophobic residues are likely to need an organic co-solvent.

Choosing a first solvent

Peptide typeFirst choiceIf it does not dissolve
Net positive (basic)Sterile purified waterA small volume of dilute acetic acid (for example 10%), then dilute with water or buffer
Net negative (acidic)Sterile purified water or bufferA small volume of dilute ammonium bicarbonate or dilute aqueous ammonia, then dilute (not recommended for cysteine-containing peptides; see below)
Neutral or highly hydrophobicA minimal volume of DMSO, or DMFAdd the aqueous buffer slowly to the dissolved peptide, mixing between additions
Strongly aggregatingDenaturants such as 6 M guanidine hydrochloride or 8 M urea, for analytical work where they are compatibleConsider whether the assay can tolerate the denaturant once diluted

Ammonium bicarbonate and acetic acid are volatile, which is useful if the material may need to be lyophilised again. Whatever you use, make sure the final solution is compatible with the assay.

Organic co-solvents

  • Dissolve first, then dilute. Dissolve the peptide completely in the organic solvent before adding aqueous buffer. Adding the buffer slowly reduces the chance of the peptide precipitating.
  • Check assay tolerance. Cell-based and enzymatic assays tolerate only limited concentrations of DMSO or DMF, often below 1% (v/v) in the final assay, and sometimes much less. Check the limit for your system and include a solvent-only control.
  • Acetonitrile is an alternative for some analytical applications, but it is usually less suitable for cell-based work.

Cysteine and methionine: the DMSO caveat

DMSO is a mild oxidant and can oxidise the side chains of cysteine and methionine. For peptides containing free cysteine, DMF is often preferred as the organic co-solvent. Free thiols also oxidise more readily at neutral to basic pH, forming disulfide-linked dimers or oligomers, so basic solvents such as ammonium bicarbonate are best avoided for these peptides. Using degassed solvents, working at slightly acidic pH where the assay allows, and preparing solutions shortly before use all help. See Peptide degradation pathways.

Test a small portion first

Before committing the whole vial, weigh out a small amount and try the intended solvent. If it fails, you can try the next option without having already diluted all of your material in a solvent you then need to remove. Note the order of solvents that worked for each sequence, as it will save time with later batches.

Helping a peptide dissolve

  • Mix gently. Swirling or gentle vortexing is usually enough. Vigorous agitation can promote foaming and aggregation.
  • Sonicate briefly. Short bursts in a bath sonicator, with the tube kept cool (for example in an ice-water bath), can break up particles. Avoid prolonged sonication, which warms the sample.
  • Look carefully. A clear-looking solution can still contain fine particles or gel. Centrifuge before use and check for a pellet; undissolved material means the true concentration is lower than calculated.
  • Avoid heat unless you have confirmed the peptide is stable at the temperature used.

Filtering

For cell culture and other work that requires sterile solutions, pass the stock through a 0.22 µm membrane filter. Choose a low protein-binding membrane (such as PVDF or PES), check that it is compatible with any organic solvent present, and be aware that some peptides, particularly hydrophobic ones, can adsorb to filters and plastics. If losses matter, measure the concentration after filtration. See Amino acid analysis and peptide quantification.

Aliquoting and storing solutions

Peptides are generally less stable in solution than as lyophilised powder. Divide the stock into single-use aliquots in low-binding tubes, store them frozen, and avoid repeated freeze-thaw cycles. Label each aliquot with the peptide, batch number, solvent, concentration and date. To calculate the concentration correctly in the first place, see Net peptide content and stock solution concentration.

Further reading

Sources and further reading

  • Kyte J, Doolittle RF. A simple method for displaying the hydropathic character of a protein. Journal of Molecular Biology. 1982;157(1):105–132.
  • Chan WC, White PD (eds). Fmoc Solid Phase Peptide Synthesis: A Practical Approach. Oxford University Press; 2000.
  • Peptide solubility and handling guidelines published by major research reagent manufacturers.

Frequently asked questions

How do I choose a first solvent?

Estimate net charge and hydrophobicity from the sequence: net positive peptides start in sterile water, net negative in water or buffer, and neutral or highly hydrophobic ones in a minimal volume of DMSO or DMF, then dilute slowly.

How do I estimate net charge?

Count +1 for each Lys, Arg and free N-terminus and -1 for each Asp, Glu and free C-terminus, with His mostly neutral at neutral pH; acetylation and amidation remove the end charges.

How much DMSO can an assay tolerate?

Cell-based and enzymatic assays often tolerate below 1% (v/v) in the final assay and sometimes much less. Check the limit for your system and include a solvent-only control.

Why dissolve in the organic solvent first?

Dissolving the peptide completely in the organic solvent and then adding aqueous buffer slowly lowers the chance of precipitation.